210-065専門知識、200-105参考資料
JPexamが提供した対応性の訓練問題をテストにして初めてCiscoの210-065専門知識に参加する受験者の最もよいな選択でございます。真実試験問題が似てるのを確保することができて一回合格するのは目標にしています。もし試験に失敗したら、弊社が全額で返金いたします。
当面の実際のテストを一致させるために、JPexamのCiscoの200-105参考資料の技術者はずべての変化によって常に問題と解答をアップデートしています。それに我々はいつもユーザーからのフィードバックを受け付け、アドバイスの一部をフルに活用していますから、完璧なJPexamのCiscoの200-105参考資料を取得しました。JPexamはそれを通じていつまでも最高の品質を持っています。
試験番号：210-065問題集試験科目：Implementing Cisco Video Network Devices v1.0
最近更新時間：2016-09-26
問題と解答：全190問 210-065専門知識
100％の返金保証。1年間の無料アップデート。
試験番号：200-105問題集試験科目：Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)
最近更新時間：2016-09-26
問題と解答：全205問 200-105参考資料
100％の返金保証。1年間の無料アップデート。
Cisco 210-065専門知識に合格することは簡単ではなくて、適切な訓练を選ぶのはあなたの成功の第一歩です。情報源はあなたの成功の保障で、JPexamの商品はとてもいい情報保障ですよ。君はJPexamの商品を選ばればCisco 210-065専門知識に合格するのを１００％保証するだけでなくあなたのために1年の更新を無料で提供します。
購入前にお試し,私たちの試験の質問と回答のいずれかの無料サンプルをダウンロード：http://www.jpexam.com/200-105_exam.html
NO.1 Refer to the exhibit.
How will the router handle a packet destined for 192.0.2.156?
A. The router will return the packet to its source.
B. The router will forward the packet via either Serial0 or Serial1.
C. The router will drop the packet.
D. The router will forward the packet via Serial2.
Answer: D
200-105試験解答 200-105段階
Explanation:
Router has pointed default router to 192.168.4.1 and this subnet is connected via serial 2 interface.
Router does not have router for the 192.0.2.156. so it will use the default gateway
192.168.4.1. A default route identifies the gateway IP address to which the router sends all IP packets
for which it does not have a learned or static route.
NO.2 Refer to the exhibit.
Which two statements are true about the loopback address that is configured on RouterB? (Choose
two.)
A. It specifies that the router ID for RouterB should be 10.0.0.1.
B. It indicates that RouterB should be elected the DR for the LAN.
C. It decreases the metric for routes that are advertised from RouterB.
D. It provides stability for the OSPF process on Router
E. It ensures that data will be forwarded by RouterB.
Answer: A,D
200-105模試エンジン 200-105受験対策解説集
Explanation:
A loopback interface never comes down even if the link is broken so it
provides stability for the OSPF process (for example we use that loopback interface as the
router-id) - B is correct.
The router-ID is chosen in the order below:
The highest IP address assigned to a loopback (logical) interface. If a loopback interface is
not defined, the highest IP address of all active router's physical interfaces will be chosen.
-The loopback interface will be chosen as the router ID of RouterB - C is correct.
NO.3 How can you disable DTP on a switch port?
A. Configure the switch port as a trunk.
B. Change the operational mode to static access.
C. Change the administrative mode to access.
D. Add an interface on the switch to a channel group.
Answer: A
200-105模試
NO.4 Refer to the exhibit.
The show interfaces serial 0/1 command was issued on the R10-1 router. Based on the output
displayed which statement is correct?
A. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is
using the default serial interface encapsulation.
B. The R10-1 router can ping the router interface connected to the serial 0/1 interface.
C. The cable connected to the serial 0/1 interface of the R10-1 router is a DTE cable.
D. The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000 bits per second.
E. The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service
provider.
Answer: A
200-105参考書勉強
Explanation:
Cisco High-Level Data Link Controller (HDLC) is the Cisco proprietary protocol for Cisco HDLC is the
default encapsulation type for the serial interfaces.
